Milnor E-P Plus Скачать руководство пользователя страница 16

Страница: 16 / 92

Pellerin Milnor Corporation

Close the line.

— If the pump does not always close the line when it is off, use a shutoff

valve to do this.

Do not let a vacuum occur.

— Supply a vacuum breaker in the chemical line that is

higher than the full level of the tank.

Flush the chemical tube with water.

— If the liquid that stays in the tube between

the pump and the machine can flow in the machine, flush the tube with water after the pump
stops.

Put the chemical tube fully below the inlet.

— It is also necessary that there is no

pressure in the chemical tube or tank when the system is off.

Figure 5.

A Configuration that Prevents Flow in the Machine When the Pump is Off (if the chemical

tube and tank have no pressure)

Schematic View

Legend

I...

Chemical inlet on the machine

L...

Chemical tube

P...

Pump

T...

Chemical tank

Prevent leaks.

— When you do maintenance on the chemical pump system:

•

Use the correct components.

•

Make sure that all connections are the correct fit.

•

Make sure that all connections are tight.

BNCJVI01 / 2018385

BNCJVI01

0000181453

D.5

1/2/20 1:16 PM

Released

1.5

Connecting Chemical Systems

BNCJVI01.C01 0000181452 C.2 D.5 C.3 1/2/20 1:16 PM Released

Multiple methods are available on E-P Plus

washer-extractors to accommodate chemical sys-

tems. Use this section to help determine the best method of chemical injection and how to connect
the chemical system. Always consult the schematic manual for this machine before connecting
chemical systems to the machine.

Commissioning

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 16 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: