Milnor E-P Plus Скачать руководство пользователя страница 63

Страница: 63 / 92

Pellerin Milnor Corporation

Table 11

Coast Times (in seconds) at Program End or Termination (cont'd.)

Model

Door Unlock

Delay (DUD)

Bath

Low Extract

High

Extract

Power-up

Delay

36026V7J

DUD

75 + DUD

85 + DUD

100

42026V6J

DUD

75 + DUD

85 + DUD

100

36026X8J

DUD

100 + DUD

150 + DUD

150

42026/42032X7J

DUD

100 + DUD

150 + DUD

150

48040F7J/B

DUD

100 + DUD

200 + DUD

160

Note:

Coast time when an extract step ends normally does not include the door unlock delay.

NOTE:

Depending on the

How to End code

, the controller will describe how the cycle

is ending and instruct the operator to press

to escape this step in the cycle.

Display or Action

Explanation

UNLOCKING THE DOOR
PLEASE WAIT

display during the last 15 seconds of coast, or during the entire
coast time if the formula was manually terminated.

WAITING TO UNLOAD

At the end of the coast time, the operator alarm sounds.

Silences the operator alarm. The door unlocks, and the machine
may be unloaded.

3.1.4

The Display During Automatic Operation

BNCJHO01.C06 0000182503 C.2 B.3 1/2/20 1:16 PM Released

Display or Action

Explanation

23:04

F02S01

02:37

TEMP A168/D170 LEV 1

These two displays alternate during normal operation.

23:04 STEP 01

02:37

TEMP A168/D170 SPD 0

23:04

F02S01

02:37

23:04 is the time remaining in the formula.

F02S01 indicates that the current formula is 02 (F02) and the cur-
rent step is 01 (S01).

02:37 is the time remaining in this step.

23:04

STEP01

02:37

STEP01 is the current step

EXTRACT indicates that the machine is currently executing an
extract.
TIMEHALT indicates that the timer is stopped while a chemical is
being injected. The chemical supplier must connect equipment for
this option.

TEMP A168/D170 LEV 2

Temperature in this machine is measured in degrees Fahrenheit or
Celsius, according to machine configuration.

Operating

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 63 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: