Milnor E-P Plus Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 92

Milnor E-P Plus Скачать руководство пользователя страница 57

Pellerin Milnor Corporation

51

For saving information

to

the data storage device or another ma-

chine, select

1=Master

at the machine controller. If two machines

are connected, establish the one which will

receive

the data as the

slave, and the

sending

machine as the master.

DATA TRANSFER

1

MASTER

The machine controller is set as the Master device, making the
storage device the slave.

NOTE:

The

Master

device is always the

sender

and

controls when the data transfer starts. The

Slave

device is

always the

receiver

and should be established and waiting

for data before the

Master

device is confirmed.

NOTICE:

Do not send data to the memory storage de-

vice until the storage device is cleared and ready to re-
ceive. The

Ready

light must be

on

when transfer begins or

the stored data will not be valid.

Confirms selection of the machine controller as the

Master

and

immediately begins the transfer.

All receiving (slave) machines

must be established before the master machine is designated.

PLEASE WAIT

AC35

TRANSFERRING DATA

While the data transfer is occurring, the four digits at the top right
of the display scroll rapidly as the machine controller sends data.

The

Receive

light on the storage device illuminates when the data

transfer begins, indicating that it is receiving data. The display on
the slave machine scrolls quickly as data is accepted.

NOTE:

Transfer times may vary somewhat, but the

average is about 75 seconds.

COMPLETED

0000

TRANSFERRING DATA

This display indicates that the machine controller deliv-

ered the data to the storage device.

The

Receive

light on the storage device goes off when the transfer

successfully ends. If all three lights on the storage device begin
blinking at any time during the transfer, the data being received
by the storage device is invalid. Clear the memory in the storage
device and perform the transfer again.

CAUTION:

Data Corruption Hazard —

If the machine controller indicates that the

data transfer is complete but the

Receive

light on the data storage device is

still illuminated, invalid data is stored in the storage device.

�

Do not rely on the data in the storage device unless the machine con-

troller indicated that the transfer completed,

AND

the

Receive

light on the

storage device turned off automatically.

�

Do not restore data from the storage device to the machine if the data is invalid. Re-

storing invalid data from the storage device to the machine controller will overwrite any
formulas that have been changed or created since the data was last stored. These formulas
can not be recovered.

«
...
55
56
57
58
59
...
»

Содержание E-P Plus





























































































Отзывы:

Нет отзывов