Milnor E-P Plus Скачать руководство пользователя страница 7

Страница: 7 / 92

Preface

BNWCUD02 / 2018256

BNWCUD02

0000189783

C.3

1/2/20 2:19 PM

Released

About This Manual

1.1

Scope

BNWCUD02.C02 0000189781 C.2 C.3 B.2 1/2/20 2:19 PM Released

This manual tells how to start, program, operate, and repair washer-extractors with the Milnor

E-P Plus

microprocessor control. See the installation manual for installation procedures and me-

chanical requirements. See the maintenance manual for maintenance and repair procedures and to
identify parts. See the schematic manual for electrical parts and electrical repair instructions.

1.2

The Normal Display at Start-up

BNWCUD02.C03 0000189780 C.2 C.3 A.6 1/2/20 2:19 PM Released

The start-up display sequence for the E-P Plus controller is described in

3.1: Running a Formula,

page 55

1.3

If this Manual Does Not Have the Necessary Data

BNUUUU03.C01 0000188801 C.2 C.3 B.4 1/2/20 2:14 PM Released

This manual has the best data that was available when your machine was made. If you cannot find
the necessary data:

•

Are you looking for data about a component not made by Milnor

but used on your ma-

chine—for example, a motor or a brake caliper?

We usually do not put the instructions of

component manufacturers in Milnor

manuals. You can find some of these instructions in the

part of the Milnor

website that gives maintenance data

(http://milnortechnicalsupport.force.

com/pkbmilnor/)

. You can also find instructions for many components on the manufacturers’

websites.

•

Are you looking for data about a Milnor

component on your machine that this manual

does not give?

If we get better data or more data after the manual is available, we will add it

to a newer version of the manual. Speak with the Milnor

Customer Support group. They can

give you newer instructions if they are available or help you if not.

1.4

Trademarks

BNUUUU02.R01 0000158093 C.2 C.3 D.2 4/6/20 2:44 PM Released

These words are trademarks of Pellerin Milnor

Corporation and other entities:

Pellerin Milnor Corporation

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 7 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: