Milnor E-P Plus Скачать руководство пользователя страница 58

Страница: 58 / 92

Pellerin Milnor Corporation

Display or Action

Explanation

Acknowledges that the data transfer is complete and returns to the

Program

menu.

PROGRAM

DATA TRANSFER

Data Transfer

menu display. Scroll to

Program

menu item

then turn the

Run/Program

keyswitch to the

Run

position.

Scroll the

Program

menu selections.

PROGRAM

TURN KEY TO RUN

From item

of the

Program

menu, return to normal operating

mode.

Return to normal operating mode. Press

if necessary to con-

firm that the key is at

Run

RUN PROGRAM00 OK TO
POWER OFF

The

Run Program

display appears to indicate that it is safe to

turn the machine off.
Turn off power to the machine(s).

Disconnect the memory storage device, remove the key, and put
both in secure locations. For two machines, remove the connect-
ing cable.

2.3.6.3

Restoring Saved Data to the Machine from the Storage Device

or Another Machine

BNCJUP05.R03 0000195423 C.2 D.2 A.6 1/2/20 1:16 PM Released

Display or Action

Explanation

Turn off power to the machine(s) before connecting the serial
memory storage device.

Connect the storage device to the machine using the 9-pin round
connector. For two machines, use a serial cable constructed as de-
scribed in

5.3: Construction of External Serial Link Cables, page

Apply power to the machine(s). The storage device receives
power through the connector from the power supply in the
machine.

RUN PROGRAM00 OK TO
POWER OFF

When the

Run Program

display appears, switch from

Run

mode

Program

mode.

Turn the

Run/Program

keyswitch on the machine controller(s)

from the

Run

position to the

Program

position.

PROGRAM

TURN KEY TO RUN

Controller display when the

Run/Program

keyswitch is set to

(

Program

position).

Scroll down in the

Program

menu to

Data Transfer

PROGRAM

DATA TRANSFER

This is the

Data Transfer

menu selection. Follow the procedure

2.3.6.2: Saving Data from the Machine to the Storage Device

Programming

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 58 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: