Milnor E-P Plus Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 92

Milnor E-P Plus Скачать руководство пользователя страница 86

80

Pellerin Milnor Corporation

Table 15.

DIP Switch Positions for E-P Plus

®

and E-P Express

®

Machines (External transmit

button required)

Processor Board

Part Number

Processor

Board Revision

Code

Machine Software

and Revision

Storage Device

Software and

Revision

DIP Switch

Setting

30015HxJ and 30022HxJ Models

08BH18EPDT

K

WUH7JA/2200E

WUNTIA/00008

E

VxJ Models

08BH18EPDT

K

WUV7J1B/2200K

WUNTIA/00008

E

30015T5X and 30022T5X Models

08BH18EPYT

K

WUEPXPRSA/22004

WUNTIA/00008

E

All E-P Express Gear Guardian Models

08BH18EPYT

K

WUT5XGGA/22GGF

WUNTIA/00008

E

08BH18EPWT

K

WUMWRXGG/(any)

WUNTIA/00008

E

Key:

A

All switch positions OFF

B

Position 4 ON; all others OFF

C

Position 5 ON; all others OFF

D

Positions 1 and 5 ON; all others OFF

E

Positions 4 and 5 ON; all others OFF

BNCUUP02 / 2018303

BNCUUP02

0000196987

A.9

1/2/20 1:30 PM

Released

5.3

Construction of External Serial Link Cables

BNCUUP02.C01 0000196986 C.2 A.9 1/2/20 1:30 PM Released

This document provides information for on-site fabrication of certain types of serial communica-
tion cables. Programmable data can be transferred between compatible machines or between a
machine and a Milnor

®

serial memory storage device

(see related note below), using the down-

load cables described in

5.3.2.2: Connecting Two or More Machines for Machine-to-machine

Transfer, page 82

and

5.3.2.3: Connecting a Machine to a Serial Memory Storage Device, page

respectively. These cable(s) connect to the cabinet-mounted 9-pin DIN type receptacle shown

in

Figure 14: 9-Pin DIN Connector Pin Identification (from wire entry side of connectors), page

and may be installed temporarily or permanently, as appropriate.

NOTE:

The currently approved printers and printer configuration settings are provided

in

5.4: Printer Requirements and Settings, page 84

. A pre-assembled machine-to-printer

cable similar to the cable described here, is available from Milnor (P/N 10YMK2PNTR).

NOTE:

The Milnor

serial memory storage device

(also known as a

download box

) con-

tains nonvolatile memory to hold a back-up copy of the programming and configuration
data for

one machine

. This data is transferred between the machine and the memory stor-

age device via the DIN receptacle on the machine. Two models are currently available:
KXMIC00507 and KXMIC00508. The already wired cable and DIN connector are in-
cluded as part of the memory storage device. Consult the Milnor Service department to
determine the correct device for a particular application.

Supplemental Information

«
...
84
85
86
87
88
...
»

Содержание E-P Plus





























































































Отзывы:

Нет отзывов