Milnor E-P Plus Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 92

Milnor E-P Plus Скачать руководство пользователя страница 82

76

Pellerin Milnor Corporation

5 Supplemental Information

BNCJUF01 / 2018385

BNCJUF01

0000190120

C.3

1/2/20 1:16 PM

Released

5.1

The E-P Plus

®

and E-P Express

®

Hardware

BNCJUF01.C01 0000190133 C.2 C.3 B.3 1/2/20 1:16 PM Released

The Milnor

®

E-P Plus

®

and E-P Express

®

microprocessor controls are designed specifically for

Milnor

®

washer-extractors. Along with certain external electromechanical relay logic and sensing

devices, they control all machine and system functions. Not every Milnor

®

microprocessor sys-

tem includes all the following components.

5.1.1

Keyswitches

BNCJUF01.C02 0000190132 C.2 C.3 A.6 1/2/20 1:16 PM Released

5.1.1.1

Run/Program Keyswitch

BNCJUF01.C03 0000190131 C.2 C.3 A.6 1/2/20 1:16 PM Released

This keyswitch allows controlling who has the necessary access to modify wash formulas. For-

mulas can be modified only when this switch is turned from the

Run

position (

) to the

Pro-

gram

position (

). To safeguard wash formulas, keep this key in a secure place with restricted

personnel access.

5.1.1.2

Automatic/Test Keyswitch (E-P Plus

®

Models Only)

BNCJUF01.C04 0000190130 C.2 C.3 B.3 1/2/20 1:16 PM Released

This keyswitch allows only employees with access to the appropriate key to operate the machine
in

Test mode

for troubleshooting.

Test mode

can be accessed only when this switch is turned

from the

Automatic

position (

) to the

Test

position (

). To reduce the risk of personal in-

jury and machine damage, keep this key in a secure place with restricted personnel access.

5.1.2

Display

BNCJUF01.C05 0000190129 C.2 C.3 A.6 1/2/20 1:16 PM Released

The display is a vacuum fluorescent display consisting of two lines of 20 characters each. This
type of display is easily identified by green characters on a black background when operating, or
a nearly black background when not operating.

5.1.3

Power Supply

BNCJUF01.C06 0000190128 C.2 C.3 A.6 1/2/20 1:16 PM Released

The power supply provides a regulated specific voltage to the processor board and certain auxili-
ary boards and devices. The power supply also converts control circuit alternating current voltage
to +12 volts direct current, –12 volts direct current, and +5 volts direct current. The power supply
is switchable between 120 volts and 240 volts alternating current input voltage.

«
...
80
81
82
83
84
...
»

Содержание E-P Plus





























































































Отзывы:

Нет отзывов