Microsens MS400870M Series страница 153 Скачать руководство пользователя

Страница: 153 / 170

153

In this page, you can find the following information of a 802.1x port:

Port:

The number of the port.

State:

Display the number of the port 802.1x link state LinkDown or LinkUp.

Last Source:

Display the number of the port

‟s Last Source.

Last ID:

Display the number of the port

‟s Last ID.

4.5.7.2 802.1X Statistics

In order to view the real-time 802.1x port statistics status of the Managed Switch, select

802.1x Statistics

from the

802.1x Monitor

menu and then the following screen page shows

up.

Select the port number from the pull-down menu to view statistics.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды

Microsens MS400870M Series, Руководство пользователя

Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды