Microsens MS400870M Series страница 63 Скачать руководство пользователя

Страница: 63 / 170

Flow Control:

None, RS-232 setting, view-only field.

Telnet Port:

Specify the desired TCP port number for the Telnet Console. The default TCP

port number of the Telnet is 23.

System Time Out:

Specify the desired time that the Managed Switch will wait before

disconnecting an inactive Console/telnet. Specifying

“0” means an inactive connection will

never be disconnected.

4.3.4 Time Server Configuration

Click the option

Time Server Configuration

from the

Network Management

menu and

then the following screen page appears.

Time Synchronization:

To enable or disable time synchronization.

Time Server Address:

NTP time server address.

2nd Time Server Address:

When the default time server is down, the Managed Switch will

automatically connect to the 2nd time server.

Synchronization Interval:

The time interval to synchronize from NTP time server.

Time Zone:

Select the appropriate time zone from the pull-down menu.

Daylight Saving Time:

To enable or disable the daylight saving time function. It is a way of

getting more daytime hour(s) by setting the time to be hour(s) ahead in the morning.

Daylight Saving Time Offset:

Click the pull-down menu to select the time offset of daylight

saving time.

NOTE:

We use SNTP to get the time from those NTP servers. It is recommended that the

time server is in the same LAN with the Managed Switch or at least not too far away. In this
way, the time will be more accurate.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды

Microsens MS400870M Series, Руководство пользователя

Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды