Microsens MS400870M Series страница 122 Скачать руководство пользователя

Страница: 122 / 170

122

Max: This shows the maximum number available for MVR VLAN configuration.

VLAN ID:

Specify a VLAN ID for multicast VLAN.

Port Members:

Indicate whether each port is a receive port, source port, or not used.

4.4.13.2 MVR Group

Select the option

MVR Group

from the

MVR Configuration

menu and then the following

screen page appears.

VLAN:

View-only field that shows the current MVR VLAN ID.

Group Range:

View-only field that shows the MVR Group Range.

Click

New

to register a new MVR Group and then the following screen page appears.

Click

Edit

to edit and view the MVR Group settings.

Click

Delete

to remove a current MVR Group.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды

Microsens MS400870M Series, Руководство пользователя

Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды