Microsens MS400870M Series страница 127 Скачать руководство пользователя

Страница: 127 / 170

127

DHCP Snooping:

Enable or disable DHCP Snooping function.

Default DHCP Initiated Time:

Specify DHCP initiated time. (4~9999 seconds)

Default DHCP Leased Time:

Specify DHCP Leased time. (4~9999 seconds)

Port Isolation:

If port isolation is set to

“Enabled”, the customer port (port 1~22) can not

communicate to each other.

IPv6 auto discovery/DHCPv6:

Enable to filter IPv6 auto discovery and DHCPv6.

UPnP:

Enable to filter UPnP packets.

4.4.14.4 Static IP Table Configuration

Select the option

Static IP Table Configuration

from the

SKA Configuration

menu and

then the following screen page appears.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды

Microsens MS400870M Series, Руководство пользователя

Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды