Microsens MS400870M Series страница 67 Скачать руководство пользователя

Страница: 67 / 170

Case Fan Trap:

Enable or disable the Managed Switch to send a trap when fan is not

working or failed.

SFP Abnormality Tray:

Enable or disable the Managed Switch to send SFP abnormality

trap.

4.3.8 Mal-attempt Log Configuration

Click the option

Trap Configuration

from the

Network Management

menu and then the

following screen page appears.

When DHCP snooping filter unauthorizes DHCP packets on the network, the Mal-attempt
log will allow the Managed Switch to send event notification message to Log server.

Log Server:

Click the Pull-down menu to enable or disable Mal-attempt log.

SNTP Status:

View-only field that shows the SNMP status.

Log Server IP-1:

Specify the default Log server IP address.

Log Server IP-2:

Specify the second Log server IP address.

Log Server IP-3:

Specify the third Log server IP address.

When the default Log Server is down, the Managed Switch will automatically contact the
second or third Log server.

4.4 Switch Management

In order to manage the Managed switch and set up required switching functions, click the
folder icon

Switch Management

from the Console main menu and then several options and

folders will be displayed for your selection.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды

Microsens MS400870M Series, Руководство пользователя

Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды