Microsens MS400870M Series Скачать руководство пользователя страница 4

Страница: 4 / 170

Table of Contents

1. INTRODUCTION ............................................................................................................... 8

1.1 Interface ....................................................................................................................... 8

1.2 Management Options ................................................................................................... 9

1.3 Management Software ............................................................................................... 10

1.4 Management Preparations ......................................................................................... 11

2. Command Line Interface (CLI) ......................................................................................... 13

2.1 Using the Local Console ............................................................................................ 13

2.2 Remote Console Management - Telnet ...................................................................... 14

2.3 Navigating CLI ............................................................................................................ 15

2.3.1 Mode and command summary ............................................................................ 15

2.3.2 General commands and quick keys ..................................................................... 19

2.3.2.1 Quick keys ..................................................................................................... 19

2.3.2.2 Listing Command .......................................................................................... 20

2.3.2.3 Show command ........................................................................................... 20

2.3.2.4 Usage Help .................................................................................................. 23

2.3.2.5 Press Any Key to Continue .......................................................................... 23

2.3.2.6 Conventions ................................................................................................. 24

2.4 User mode .................................................................................................................. 24

2.5 Enable mode .............................................................................................................. 26

2.5.1 Backup command mode ..................................................................................... 26

2.5.2 CFM command mode ......................................................................................... 27

2.5.3 Console command mode .................................................................................... 28

2.5.4 IP command mode .............................................................................................. 28

2.5.5 Service command mode ..................................................................................... 29

2.5.6 Syslog command mode ...................................................................................... 32

2.5.7 System command mode ..................................................................................... 32

2.5.8 Time-server command mode .............................................................................. 32

2.5.9 Upgrade command mode ................................................................................... 32

2.5.10 User command mode ........................................................................................ 33

2.6 Config mode ............................................................................................................... 34

2.6.1 Aggr command mode .......................................................................................... 35

2.6.2 CFM command mode ......................................................................................... 36

2.6.3 Dot1x command mode ........................................................................................ 38

2.6.4 IGMP filter command mode ................................................................................ 39

2.6.5 IGMP command mode ........................................................................................ 40

2.6.6 MAC command mode ......................................................................................... 40

2.6.7 Mirror command mode ........................................................................................ 41

2.6.8 MVR command mode ......................................................................................... 41

2.6.9 Port command mode ........................................................................................... 43

2.6.10 QoS command mode ......................................................................................... 43

2.6.11 RSTP command mode ....................................................................................... 46

2.6.12 SKA command mode ......................................................................................... 48

2.6.13 Multicast command mode .................................................................................. 49

2.6.14 Switch command mode ..................................................................................... 50

2.6.15 VLAN command mode ....................................................................................... 50

3. SNMP NETWORK MANAGEMENT................................................................................. 53

4. WEB MANAGEMENT ...................................................................................................... 54

4.1 System Information .................................................................................................... 56

4.2 User Authentication .................................................................................................... 57

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Microsens MS400870M Series, Руководство пользователя, Страница: 4 / 170

Результаты поиска

Содержание MS400870M Series

Отзывы: