Microsens MS400870M Series страница 40 Скачать руководство пользователя | Manualshive

Страница: 40 / 170

background image

40

filter <port_list> <profile_name>
<profile_name>…

This allows information of specified IPMC
Profile to pass-through.

<port_list>: 1~26
<profile_name> This field for IPMC Profile
name is from the entry registered in IPMC
Profile option.

For example:

Console(config-igmpfilter)# filter 1-4 mypro

2.6.5 IGMP command mode

Prompt

Command & Parameter

Description

Console(config-
igmp)#

mode <enable | disable>

To enable or disable IGMP function.

router-port <port_list>

To set up which ports belong to router ports

<port_list>: 1~26

For example:

Console(config-igmp)# router-port 1-4,10-
15,18,19

flooding <enable | disable>

Set forwarding mode for unregistered (not-joined)
IP multicast traffic. The traffic will flood when
enabled. However, the traffic will forward to router-
ports only when disabled.

vlanstate <vid> <enable |
disable>

When enabled, the port in VLAN will monitor
network traffic and determine which hosts want to
receive the multicast traffic.

<vid>: 1~4094

For example:

Console(config-igmp)#vlanstate 1 enable

vlanquerier <vid> <enable |
disable>

When enabled, the port in VLAN can serve as the
Querier which is responsible for asking hosts
whether they want to receive multicast traffic.

<vid>: 1~4094

For example:

Console(config-igmp)#vlanquerier 1 enable

interval <num>

The Query Interval is used to set the time
between transmitting IGMP queries.

<num>:1~6000 Seconds

maxresponse <num>

This determines the maximum amount of time
allowed before sending an IGMP response report.

<num>: 1~6000(1/10Secs)

fast-leave <enable | disable>

The Fast Leave option may be enabled or
disabled. This allows an interface to be ignored
without sending group-specific queries.

2.6.6 MAC command mode

Prompt

Command & Parameter

Description

«
...
38
39
40
41
42
...
»

Содержание MS400870M Series











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MS400870M Series

Бренд: steute Страницы: 20

Бренд: Exsys Страницы: 14

Бренд: Manhattan Страницы: 4

Liquipoint FTW33

Бренд: Endress+Hauser Страницы: 48

Бренд: Dusun Страницы: 18

Бренд: Enable-IT Страницы: 49

Бренд: Alps Electric Страницы: 4

Бренд: Linksys Страницы: 110

Бренд: Epcom Страницы: 2

Бренд: Rocstor Страницы: 2

Бренд: Netis Страницы: 8

Бренд: EnGenius Страницы: 72

Бренд: ABB Страницы: 9

Бренд: CYP Страницы: 44

Бренд: CYP Страницы: 48

Бренд: Inficon Страницы: 18

ThunderSync3-16

Бренд: CAMBRIONIX Страницы: 12

Бренд: Cambium Networks Страницы: 648

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды