Microsens MS400870M Series Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 170

Microsens MS400870M Series Скачать руководство пользователя страница 139

139

4.4.15.7 Y.1731 Round-Trip Delay Measurement

Select the option

Delay Measurement

from the

CFM Configuration

menu and then the

following screen page appears.

Domain:

Select a current registered Maintenance Domain.

Association:

Select a current registered Maintenance Association.

Source MEP:

View-only field that shows the current MEP ID.

Target MAC/MEP ID:

Specify the target MAC or MEP ID for link trace test.

Messages Number:

Specify the Number from 2~100.

VLAN Priority:

Specify the VLAN priority-bit for loopback test.

Send Message:

Start Delay Measurement.

4.4.16 Access Control List Management (ACLM)

Creating an access control list allows users to define who has the authority to access
information or perform tasks on the network. In the Managed Switch, users can establish
rules applied to port numbers to permit or deny actions.

Select the folder

Access Control List Management

from the

Switch Management

menu

and then the following screen page appears.

ACL Ports Configuration:

When information does not conform to MAC and VLAN parameters, actions set in ACL Ports

«
...
137
138
139
140
141
...
»

Содержание MS400870M Series











































































































































































Отзывы:

Нет отзывов