Microsens MS400870M Series Скачать руководство пользователя страница 5

Страница: 5 / 170

4.2.1 RADIUS Configuration ......................................................................................... 59

4.3 Network Management ................................................................................................ 60

4.3.1 Network Configuration ......................................................................................... 60

4.3.2 System Service Configuration.............................................................................. 61

4.3.3 RS232/Telnet/Console Configuration ................................................................... 62

4.3.4 Time Server Configuration ................................................................................... 63

4.3.5 Device Community ............................................................................................... 64

4.3.6 Trap Destination ................................................................................................... 65

4.3.7 Trap Configuration ............................................................................................... 66

4.3.8 Mal-attempt Log Configuration ............................................................................. 67

4.4 Switch Management ................................................................................................... 67

4.4.1 Switch Configuration ............................................................................................ 69

4.4.2 Port Configuration ................................................................................................ 70

4.4.3 Link Aggregation .................................................................................................. 71

4.4.3.1 Trunk Mode Configuration ............................................................................. 72

4.4.3.2 Port Trunking ................................................................................................. 73

4.4.3.3 LACP Port Configuration ............................................................................... 74

4.4.4 Rapid Spanning Tree ........................................................................................... 76

4.4.4.1 RSTP Switch Settings ................................................................................... 77

4.4.4.2 RSTP Aggregated Port Settings .................................................................... 78

4.4.4.3 RSTP Physical Port Settings ......................................................................... 80

4.4.5 802.1X Configuration ........................................................................................... 83

4.4.5.1 Configure System .......................................................................................... 83

4.4.5.2 Configure Port Admin State ........................................................................... 84

4.4.5.3 Configure Port Reauthenticate ...................................................................... 85

4.4.6 MAC Address Management ................................................................................. 86

4.4.6.1 MAC Table Learning ...................................................................................... 87

4.4.6.2 Static MAC Table Configuration ..................................................................... 87

4.4.7 VLAN Configuration ............................................................................................. 89

4.4.7.1 Port-Based VLAN .......................................................................................... 89

4.4.7.2 802.1Q VLAN Concept .................................................................................. 91

4.4.7.3 802.1Q VLAN ................................................................................................ 94

4.4.7.3.1 Configure VLAN ...................................................................................... 95

4.4.7.3.2 Configure VLAN Aware ........................................................................... 96

4.4.7.3.3 Configure Ingress Filter .......................................................................... 97

4.4.7.3.4 Configure Frame Type ............................................................................ 97

4.4.7.3.5 Configure Port VLAN ID .......................................................................... 98

4.4.7.3.6 Configure Port Egress Mode .................................................................. 99

4.4.8 QoS Configuration ............................................................................................... 99

4.4.8.1 QoS Port Configuration ............................................................................... 100

4.4.8.2 QoS Control List .......................................................................................... 103

4.4.8.3 QoS Rate Limiter ......................................................................................... 105

4.4.8.4 Storm Control .............................................................................................. 106

4.4.9 DSCP Remark ................................................................................................... 107

4.4.10 Port Mirroring ................................................................................................... 109

4.4.11 IGMP Snooping ................................................................................................ 110

4.4.11.1 IGMP Configuration .................................................................................... 111

4.4.11.2 IGMP VLANID Configuration ..................................................................... 112

4.4.11.3 IPMC Segment .......................................................................................... 113

4.4.11.4 IPMC Profile .............................................................................................. 114

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Microsens MS400870M Series, Руководство пользователя, Страница: 5 / 170

Результаты поиска

Содержание MS400870M Series

Отзывы: