Microsens MS400870M Series Скачать руководство пользователя страница 55

Страница: 55 / 170

1. System Information:

Name the Managed Switch, specify the location and check the

current version of information.

2. User Authentication:

View the registered user list. Add a new user or remove an

existing user.

3. Network Management:

Set up or view the IP address and related information of the

Managed Switch required for network management applications.

4. Switch Management:

Set up switch/port configuration, VLAN configuration and other

functions.

5. Switch Monitor:

View the operation status and traffic statistics of the ports.

6. System Utility:

Ping, Firmware Upgrade, Load Factory Settings, etc.

7. Save Configuration:

Save all changes to the system.

8. Reset System:

Reset the Managed Switch.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Microsens MS400870M Series, Руководство пользователя, Страница: 55 / 170

Результаты поиска

Содержание MS400870M Series

Отзывы: