manualshive.com logo in svg

Microsens MS400870M Series, Руководство пользователя, Страница: 155 / 170

Поделиться
Скачать
Microsens MS400870M Series Скачать руководство пользователя страница 155

 

 

155 

 
The  IGMP  querier  periodically  sends  IGMP  general  queries  to  all  hosts  and  routers 
(224.0.0.1) on the local subnet to find out whether active multicast group members exist on 
the subnet.  
 
Upon receiving an IGMP general query, the Managed Switch forwards it through all ports in 
the VLAN except the receiving port. 
 

Querier:

 The state of IGMP querier in the VLAN. 

 

Queries  Transmitted:

  The  total  IGMP  general  queries  transmitted  will  be  sent  to  IGMP 

hosts. 
 

Queries Received:

 The total received IGMP general queries from IGMP querier. 

 

v1 Reports: 

IGMP Version 1 reports.

 

 
v2 Reports: 

IGMP Version 2 reports.

 

 
v3 Reports: 

IGMP Version 3 reports.

 

 
v2 Leaves: 

IGMP Version 2 leaves.

 

 

4.5.8.2 IGMP Group Table 

 

In  order  to  view  the  real-time  IGMP  multicast  group  status  of  the  Managed  Switch,  select 

IGMP  Group  Table 

from  the 

IGMP  monitor 

menu  and  then  the  following  screen  page 

appears. 
 

 

 
Update:

 Click 

“Update” to update the table. 

 

Содержание MS400870M Series











































































































































































Отзывы:

Нет отзывов