manualshive.com logo in svg

Microsens MS400870M Series, Руководство пользователя, Страница: 13 / 170

Поделиться
Скачать
Microsens MS400870M Series Скачать руководство пользователя страница 13

13 

2. Command Line Interface (CLI) 
 

This chapter introduces you how to use your MS400870M Series CLI, specifically in: 
 

  Local Console 

  Telnet 

  Configuring the system 

  Resetting the system 

 
The interface and options in Local Console and Telnet are the same.  The major difference 
is the type of connection and the port that is used to manage the Managed Switch.  

 

 

2.1 Using the Local Console 

 
Local  Console  is  always  done  through  the  RS-232  DB-9  port  and  requires  a  direct 
connection  between  the  switch  and  a  PC.  This  type  of  management  is  useful  especially 
when the network is down and the switch cannot be reached by any other means. 
 
You also need the Local Console Management to setup the Switch network configuration for 
the first time.  You can setup the IP address and change the default configuration to desired 
settings to enable Telnet or SNMP services. 
 
Follow these steps to begin a management session using Local Console Management: 
 

Step 1.

 

Attach the serial cable the RS-232 DB-9 port located at the back of the Switch 
with a null modem. 

 

Step 2.

 

Attach the other end to the serial port of a PC or workstation. 

 

Step 3.

 

Run a terminal emulation program using the following settings: 

 

 

Emulation   

VT-100/ANSI compatible 

 

BPS   

 

9600 

 

Data bits 

 

8 

 

Parity  

 

None 

 

Stop bits 

 

1 

 

Flow Control 

None 

 

Enable 

 

Terminal keys 

 

Step 4.

 

Press Enter to access the CLI (Command Line Interface) mode. 

 

Содержание MS400870M Series











































































































































































Отзывы:

Нет отзывов