Microsens MS400870M Series Скачать руководство пользователя страница 69

Страница: 69 / 170

14. CFM Configuration:

Set up CFM maintenance domain, maintenance association,

maintenance end point list, maintenance end port settings, loopback testing and
linktrace testing.

15. Access Control List Management:

Set up access control list ports and rate limiter.

4.4.1 Switch Configuration

Click the option

Switch Configuration

from the

Switch Management

menu and then the

following screen page appears.

Maximum Frame Size:

Specify the maximum frame size between 1518 and 9600 bytes.

The default maximum frame size is 9600bytes.

MAC Address Aging Time:

Specify MAC Address aging time between 0 and 1048575

seconds.

SFP Safety Temperature:

Enter the specific temperature for the Managed Switch to detect

the SFP DMI safety range. (Default 0~70C)

SFP Safety Voltage:

Enter the specific Voltage for the Managed Switch to detect the SFP

DMI safety range. (Default 3~3.6V)

SFP Safety TX Bias:

Enter the specific Bias for the Managed Switch to detect the SFP DMI

safety range. (Default 400mA)

Layer 2 Control Protocol:

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Microsens MS400870M Series, Руководство пользователя, Страница: 69 / 170

Результаты поиска

Содержание MS400870M Series

Отзывы: