Microsens MS400870M Series страница 156 Скачать руководство пользователя

Страница: 156 / 170

156

VLAN ID:

VID of the specific VLAN

Group:

The multicast IP address of IGMP querier.

Port:

The port(s) grouped in the specific multicast group.

4.5.9 MAC Address Table

MAC Address Table

displays MAC addresses learned when System Reset and MAC

Address Learning are enabled.

The table above shows the MAC addresses learned from each port of the Managed Switch.

Click

Update

to update the MAC Address Table.

Click

Clear

to clear the MAC Address table.

4.5.10 SFP Information

4.5.10.1 SFP Port Information

SFP Information

displays each port

‟s slide-in SFP Transceiver information e.g. Speed,

Length, Vendor Name, Vendor PN, Vendor SN, and detection Temperature, Voltage , TX
Bias, etc. Select

SFP Port Info

from

the

SFP Information

menu and then the following

screen page appears.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды

Microsens MS400870M Series, Руководство пользователя

Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды