Microsens MS400870M Series страница 135 Скачать руководство пользователя

Страница: 135 / 170

135

4.4.15.3 Maintenance End Point List

Select the option

Maintenance End Point List

from the

CFM Configuration

menu and

then the following screen page appears.

MA Name:

View-only field that shows the MA Name of the selected MD.

MEP LIST:

View-only field that shows a list of remote MEP IDs.

MEP ID:

Specify the remote MEP ID which you want to add or remove.

Status:

Idle:

No actions will be taken.

Add:

Insert a specified MEP ID to the MEP List.

Delete:

Remove a specified MEP ID from the MEP List.

4.4.15.4 Maintenance End Point Settings

Select the option

Maintenance End Point Settings

from the

CFM Configuration

and then the following screen page appears.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды

Microsens MS400870M Series, Руководство пользователя

Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды