Microsens MS400870M Series страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 170

background image

2

Trademarks

Contents subject to revise without prior notice.
All other trademarks remain the property of their respective owners.

Copyright Statement

Copyright



2008, All Rights Reserved.

This publication may not be reproduced as a whole or in part, in any way whatsoever unless prior
consent has been obtained from Company.

FCC Warning

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class-A  digital  device,
pursuant  to  Part  15  of  the  FCC  Rules.  These  limitations  are  designed  to  provide  reasonable
protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates  uses
and  can  radiate  radio  frequency  energy.    If  this  equipment  is  not  installed  properly  and  used  in
accordance with the instructions, may cause harmful interference to radio communications. However,
there  is  no  guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into a different outlet from that the receiver is connected.



Consult your local distributors or an experienced radio/TV technician for help.



Shielded interface cables must be used in order to comply with emission limits.

Changes or modifications to the equipment, which are not approved by the party responsible for
compliance, could affect th

e user‟s authority to operate the equipment.

Copyright © 2008 All Rights Reserved.

Company has an on-going policy of upgrading its products and it may be possible that information in
this document is not up-to-date. Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without written consent from the
company.

Trademarks:
All trade names and trademarks are the properties of their respective companies.

«
1
2
3
4
...
»

Содержание MS400870M Series











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MS400870M Series

DUB-H4 - Hub - USB

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: WAGO Страницы: 39

Бренд: Handic Страницы: 2

Matrix DFE-Gold 4G4202-60

Бренд: Enterasys Страницы: 78

Бренд: ZENEC Страницы: 16

Бренд: NETGEAR Страницы: 8

Бренд: protech Страницы: 4

IPS-800CE-D16, IPS-1600CE-D16

Бренд: Western Telematic Страницы: 58

Бренд: EtherWAN Страницы: 2

Бренд: EtherWAN Страницы: 2

Бренд: SMC Networks Страницы: 6

Бренд: ICCN Страницы: 48

AVS-OCT-3264-360

Бренд: AMX Страницы: 1

Бренд: Icy Box Страницы: 12

kontron KSwitch D3 UMP

Бренд: S&T Страницы: 36

QSW-M2108 Series

Бренд: QNAP Страницы: 28

CrossPoint 42 HVA

Бренд: Extron electronics Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды