Microsens MS400870M Series страница 132 Скачать руководство пользователя

Страница: 132 / 170

132

Current/Max Domain:

View-only field.

Current:  This shows the number of current registered Maintenance Domain.
Max:  This shows the maximum number available for Maintenance Domain
registration. The default number is 20.

MD Name:

Specify a unique ID for a newly registered MD.

MD Format:

Currently, the only supported MD format is

“String”.

MD Level:

Specify a service level.

MHF:

Select an option for Maintenance Point Function from the pull-down menu.

Default:

MHFs can be created for this VID on any Bridge Port through which the VID can

pass.

Explicit:

MHFs can be created on CFM VLAN member port and only if there is a MEP at

the lower active MD-level on the port.

None:

No MHFs can be created for this VID.

Содержание MS400870M Series











































































































































































Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды

Microsens MS400870M Series, Руководство пользователя

Результаты поиска

Содержание MS400870M Series

Отзывы:

Похожие инструкции для MS400870M Series

Бренды по названию

Популярные бренды