manualshive.com logo in svg

Microsens MS400870M Series, Руководство пользователя, Страница: 165 / 170

Поделиться
Скачать
Microsens MS400870M Series Скачать руководство пользователя страница 165

 

 

165 

 

 

 

1.  Event  Log: 

Event  log  can  keep  a  record  of

 

system

‟s log events such as system warm 

start,  cold  start,  link  up/down,  user  login/logout,  etc.    They  will  be  kept  only  when  your 
CPU  version  is  A06  with  Boot  ROM  version  A08  or  later  version.  If  your  CPU  or  Boot 
ROM  version  is  earlier  than  the  one  mentioned  above,  all  events  will  lose  when  the 
system is shut down or rebooted.  

 
 

2.  Update: 

This

 

allows  users  to  update  the  latest  firmware,  save  current  configuration  or 

restore previous configuration to the Managed Switch.  

 
 

3.  Load  Factory  Setting: 

Load  Factory  Setting  will  set  the  configuration  of  the  Managed 

Switch back to the factory default settings. The IP and Gateway addresses will be set to 
the factory default as well.  

 
 

4.  Load  Factory  Setting  Except  Network  Configuration: 

Selecting this function will also 

restore  the  configuration  of  the  Managed  Switch  to  its  original  factory  default  settings. 
However, this will not reset the IP and Gateway addresses to the factory default.  

 

5. Backup Configuration: 

Set up the configuration for backup.

 

 

4.6.1 Event Log 

 

Event log

 keep a record of user login, logout timestamp information.  Select 

Event Log 

from the 

System Utility 

menu and then the following screen page appears. 

 

Содержание MS400870M Series











































































































































































Отзывы:

Нет отзывов