Micromeritics AccuPyc 2 1340 Скачать руководство пользователя страница 86

Страница: 86 / 158

Troubleshooting

AccuPyc II 1340

5-2

Aug 2013

What Happened

Why

What To Do

Specified pressure not
reached or maintained.

(continued)

There are gas leaks in
the cell chamber or
expansion chamber.

Check the pycnometer for leaks (refer to

Checking the Cell and Expansion
Chambers for Leaks

, page

5-7

The Helium tank is
empty.

Replace the tank. Minimum
recommended pressure is 200 psig.

The cylinder Shut-Off
valve is closed.

Open the Shut-Off valve.

The pressure regulator is
defective, or the pressure
is set too low.

Ensure that the regulator is set properly.
Call a Micromeritics Service Represen-
tative, if necessary.

The zero offset (of
pressure transducer) is
too low.

Check offset by opening the chamber
cap. If the offset is negative, run a new
zero offset (refer to

Zero

, page

3-37

Dust filter on 2000 cm

unit is clogged or
leaking to atmosphere.

Clean the dust filter. Refer to

Cleaning

the Dust Filter (2000-cm3 units only)

page

5-9

Helium drained from
tank.

Leaks in the gas line
connection.

Pressurize the system. Close, then open
the Cylinder Shut-Off Valve. If the
needle on the pressure gauge on the gas
cylinder jumps abruptly, a leak in the
gas line connections may be indicated.
Check gas line connections.

The pycnometer was left
in manual mode with all
valves open, or the fill
valve is open and the
chamber cap is off.

Close all valves, then attach a new tank
of helium.

Содержание AccuPyc 2 1340






























































































































































Результаты поиска

Содержание AccuPyc 2 1340

Отзывы:

Похожие инструкции для AccuPyc 2 1340

Бренды по названию

Популярные бренды

Micromeritics AccuPyc 2 1340, Руководство оператора

Результаты поиска

Содержание AccuPyc 2 1340

Отзывы:

Похожие инструкции для AccuPyc 2 1340

Бренды по названию

Популярные бренды