Micromeritics AccuPyc 2 1340 Скачать руководство пользователя страница 103

Страница: 103 / 158

AccuPyc II 1340

Appendix A

Oct 2013

A-3

ANLSERR: Underrange
NN/ZZ cycles completed

Automatic operation
has been canceled

CAL_ERR: Reset Pressure Cal. ?

CAL_ERR: Temperature
Calibration Failed

Cause:

A pressure underrange occurred during an analysis because an error
occurred in the pressure measurement electronics.

Action:

Call a Micromeritics Service Representative.

Cause:

The automatic operation has been canceled by the user.

Action:

Wait for the termination process to complete or end the termination
process by pressing

Alt + CLEAR

two more times.

Cause:

The calibration information could not be read from the command or
analysis module.

Action:

Choose

Yes

and press

Enter

to reset the pressure and temperature

calibration to nominal values. Resetting to nominal may restore
normal readings but a proper calibration should be performed by a
service technician. See the section

Reset Pressure Calibration

in the

System Commands

section.

Action:

Choose

to avoid resetting the calibration. The instrument will be

unresponsive.

Cause:

The temperature calibration was unsuccessful.

Action:

Contact your service representative.

Содержание AccuPyc 2 1340






























































































































































Результаты поиска

Содержание AccuPyc 2 1340

Отзывы:

Похожие инструкции для AccuPyc 2 1340

Бренды по названию

Популярные бренды

Micromeritics AccuPyc 2 1340, Руководство оператора

Результаты поиска

Содержание AccuPyc 2 1340

Отзывы:

Похожие инструкции для AccuPyc 2 1340

Бренды по названию

Популярные бренды