Micromeritics AccuPyc 2 1340 Скачать руководство пользователя страница 53

Страница: 53 / 158

AccuPyc II 1340

System Commands

Aug 2013

3-19

Does not display for Specify

Displays when you choose

DHCP

for the first time.

Press

ENTER

; the system automatically tries to assign an IP

address. If the system is able to determine an address, the
following prompt containing the assigned address is
displayed.

If an address cannot be determined, this prompt is
displayed.

Press

Alt + CLEAR

to cancel the operation and return to the

Reload

prompt. Contact your IT Department, or choose the

Specify

option and enter the appropriate information.

Does not display for DHCP

Displays when you choose

Specify

, enabling you to enter

an appropriate IP address.

This is a numerical field in the following format:
nnn.nnn.nnn.nnn

Enter the address and press

ENTER

Does not display for DHCP

Displays this prompt so that you can enter the subnet mask
number.

This field is also numerical in the same format as the IP
address.

Enter the subnet mask number and press

ENTER

Unit[n]

SN1234 10 cm3

Communications
Requesting Address
[ENTER} to continue

Unit[n]

SN1234 10 cm3

Communications
Assigned Address:
(assigned address)

Unit[n]

SN1234 10 cm3

Communications
Requesting Address
[ENTER} to continue

Unit[n]

SN1234 10 cm3

Communications
Requesting Address
[ESC} to cancel.

Unit[n]

SN1234 10 cm3

Communications
IP Address:
(user-entered)

Unit[n]

SN1234 10 cm3

Communications
Subnet Mask:
(user-entered)

Содержание AccuPyc 2 1340






























































































































































Результаты поиска

Содержание AccuPyc 2 1340

Отзывы:

Похожие инструкции для AccuPyc 2 1340

Бренды по названию

Популярные бренды

Micromeritics AccuPyc 2 1340, Руководство оператора

Результаты поиска

Содержание AccuPyc 2 1340

Отзывы:

Похожие инструкции для AccuPyc 2 1340

Бренды по названию

Популярные бренды