Mack M359 Скачать руководство пользователя страница 67

Страница: 67 / 332

DRIVING TIPS

DRIVING ON A SLIPPERY ROAD

Driving on a Slippery

Road Surface

Although your vehicle is equipped with

many traction enhancing features, the

most effective action is to adapt your

speed to the present driving conditions.

Differential Lock

On an extremely slippery surface, you

can engage the differential lock so that

the wheels drive at the same speed.

Drive carefully when you have the

differential lock engaged. Do not forget

to disengage it when you leave the

slippery area. If you drive with the

differential lock engaged on firm ground

you risk damaging the driven axles and

wheels.

Weight Distributed over Drive

Axle

For a better grip on slippery road

surfaces you can temporarily redistribute

the weight on the driving axle.

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды