Mack M359 Скачать руководство пользователя страница 192

Страница: 192 / 332

STARTING AND DRIVING

TIRE TEMPERATURE SYSTEM

The cavity air temperature of each

programmed tire is monitored via the

Driver Information Display (DID). The

system monitors cavity air temperature

in all tires independently. If the tire cavity

temperature reaches 77°C (170°F) the

system alerts the operator. All

associated telltales display in the

instrument cluster. A tire temperature

DID screen displays. There is also an

audible alert.

NOTE

For additional information about the Tire

Monitoring System refer to the Tire

Monitor sub-section of the Driver

Information Display (DID) section.

If the tire temperature is excessively

high, the Tire Temperature HIGH screen

displays in the DID. The Check and Tire

Warning icons display in the Instrument

Cluster (IC).

To acknowledge the tire temperature

warning, press the Enter button on the

right-hand steering stalk.
The Tire Monitor screen displays. The

tire with a high temperature reading is

highlighted in the DID.

182

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды