Mack M359 Скачать руководство пользователя страница 33

Страница: 33 / 332

INTRODUCTION

WARRANTY CERTIFICATES

Standard

Normal Duty

Standard

Heavy Duty

Standard

Severe Duty

Weight Class

Qualifications

Vehicle must have

GVWR ≤ 63,000 lbs. (≤ 28 metric ton)

GCWR ≤ 110,000 lbs. (≤ 50 metric ton)

Vehicle must have

GVWR ≤ 80,000 lbs. (≤ 36 metric ton)

GCWR ≤ 143,000 lbs. (≤ 65 metric ton)

Vehicle must have

GAWR > 46,000 lbs. (> 21

metric ton)

GVWR > 80,000 lbs. (> 36

metric ton)

GCWR > 143,000 lbs. (>

65 metric ton)

Basic Coverage *

12 months or

100,000 miles (160 934 km)

12 months or

100,000 miles (160 934 km)

12 months or

100,000 miles (160 934

km)

Chassis Towing

Towing/Road Service coverage is limited to 90 days or 5,000 miles (8047 km), whichever

occurs first, and to a single tow per incident to the nearest authorized Mack Trucks service

center. Charges in excess of $1,000.00 are not covered unless Mack OneCall™ service is

contacted and approves additional amounts prior to tow.

Not Applicable

Air Conditioning

Air conditioning (sealed system only) is covered for 12 months with no mileage limitation.

Engine / Emission

Not covered under this warranty certificate. See respective engine manufacturer’s warranty certificate.

See paragraph 19 under Exclusions.

Transmission,

Driveline, Rear Axle,

Front Non-Drive

Steer Axle

36 months or 350,000 miles (563 270 km)

Covered Components are as follows:

• Manual Transmission – Transmission Assembly

• Driveline – Bearings, Hangers and Shafts

• Rear Axle – Differential Carrier Assembly and Axle Housing

• Front Non-Drive Steer Axle – Axle Beam, Steering Knuckle, and Tie Rod

12 months or

100,000 miles (160 934

km)

Allison Automatic Transmissions are not covered under this warranty certificate. See paragraph 19 under Exclusions.

Mack Carrier & Axle

Housing

60 months or

500,000 miles (804 672 km)

36 months or

300,000 miles (482 803 km)

12 months or

100,000 miles (160 934

km)

Mack T300

Transmission

60 months or

750,000 miles (1 207 008 km)

36 months or

400,000 miles (643 738 km)

12 months or

100,000 miles (160 934

km)

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды