Mack M359 Скачать руководство пользователя страница 301

Страница: 301 / 332

MAINTENANCE, LUBRICATION AND SERVICE

CHASSIS MAINTENANCE

Springs

The spring package is fastened to the

axle beam with U-bolts. It is important

that the U-bolt nuts are properly

tightened. The nuts may loosen up with

time. Severe service will loosen them

faster. Loose U-bolts can cause springs

to break, axle misalignment, hard

steering and abnormal tire wear. Inspect

the chassis for broken springs, shocks,

loose or broken axle U-bolts. If any of

these are found, contact your local

Mack dealer.

Spring Bushings

When lubricating the springs, lift the axle

off of the floor, suspend the frame with

axle stands and lower the axle. The

spring bushings are now in the position

where grease can be added to the

contact surfaces. If the spring bushings

are greased without taking the load off,

high wear and lower lifetime will occur

because grease is not able to reach the

contact surfaces. If the vehicle is for

severe service applications, increase the

frequency of spring bushing lubrication.

Rubber Bushings

Rubber bushings are used for extended

service life. If your vehicle is equipped

with rubber bushings DO NOT lubricate

them. Replace the leaf spring if it is

damaged or has premature or excessive

wear.

291

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды