Mack M359 Скачать руководство пользователя страница 324

Страница: 324 / 332

EMERGENCY ACTION

TOWING

Parking Brake Mechanical

Release (Drum Brakes)

The parking brake can be released

mechanically if compressed air is not

available.
• Remove the cap on the end of the

parking brake cylinder. Remove the

t-bolt from the canister by loosening

the nut, and insert into the hole

matching the slots on canister to t-

bolt. The bolt needs to be turned 1/4

turn and then securely tighten the

nut.

• Remember to remove the t-bolt and

secure in its original location, and

put the protective cap back on the

parking brake cylinder when towing

is completed.

NOTE

Do not remove the split pins from designs

which have a split pin. Instead unscrew

the screw and nut together.

Park Brake Release Screw

314

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды