Mack M359 Скачать руководство пользователя страница 321

Страница: 321 / 332

EMERGENCY ACTION

TOWING

Unloading

If circumstances allow, unload the

vehicle before lifting the rear

suspension.
The vehicle is unloaded to reduce the

axle loading on the towing vehicle, limit

the loading on the vehicle's lifting points

to minimize the risk of damage to the

towing vehicle.
If it is not possible to unload the vehicle

where it is, it can be towed a short

distance to a suitable place where

unloading can take place.

Maximum Loading During

Lifting and Towing

This information specifies the loading

which can be applied when using a

towing hook, towing hitch cross-

member, axles and or torque stay

anchorages.
Single Towing Hook: The hook must not

be loaded by more than the vehicle's

gross weight.
Double Towing Hooks: Each hook must

not be loaded by more than half the

vehicle's gross weight.
Towing Hitch, Towing Hitch Cross-

Member: max. 200 mm (7.8 inches) from

center of member web
• Lengthways: 20 tons

• Vertically (lift): 7 tons
• Sideways: 17 tons

Axles, Front And Rear:
• Static loading, lengthways and

vertically: 2 times axle loading

• Dynamic, e.g. during towing: 1 times

axle loading

Air Suspension Vehicles, Front Torque

Stays:
Per side: max 5 tons

Gross: max 9.5 tons

DANGER

Do not use the tow eyes for raising the

front of the vehicle; the tow eyes can

break. Do not crawl under a vehicle

suspended by tow eyes. Failure to follow

these instructions can result in serious

personal injury or death.

NOTE

The towing hooks on the vehicle must

only be used for towing.

311

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды