Mack M359 Скачать руководство пользователя страница 158

Страница: 158 / 332

STARTING AND DRIVING

USE OF BIODIESEL

Mack engines are certified to comply

with U.S. EPA and California emissions

standards based upon the use of test

fuels with specifications established by

these regulatory agencies. Alternative

fuels, including biodiesel, that are not

substantially similar to the required test

fuels may adversely affect engine

emissions compliance and may impact

the performance of certain emissions

aftertreatment components. As a result,

Mack does not warrant the engine will

conform to applicable Federal or

California emissions limits when

operated on, or having been operated

on, biodiesel or other alternative fuels

that are not substantially similar to

specified test fuels used for certification.
The use of biodiesel up to a maximum of

10% (B10) in and of itself, will not affect

the manufacturer's mechanical warranty

as to engine or emissions system,

provided the bio fuel used in the blend

conforms to ASTM D6751, and B1 to B5

blends conform to ASTM D975, and B6

to B10 blends conform to ASTM D7467.

148

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды