Mack M359 Скачать руководство пользователя страница 269

Страница: 269 / 332

MAINTENANCE, LUBRICATION AND SERVICE

ELECTRICAL SYSTEM

No.

Rated

curren

Function

FE11

10 A

ABS IGNITION

FE12

(CB)

20 A

FUEL HEAT

FE13

(CB)

15 A

AIR DRYER

FE14

5 A

TPM

FE15

5 A

APADS

FE16

SPARE

FE17

SPARE

FE18

SPARE

FE19

15 A

ALLISON TRANS

FE19

30 A

EATON TRANS

FE20

20 A

TRAILER TURN L

FE21

20 A

TRAILER TURN R

FE22

SPARE

FE23

SPARE

FE24

SPARE

FE25

SPARE

Relays

No.

Function

RE01

TRAILER STOP LAMPS

RE02

TRAILER CLEARANCE LAMPS

RE03

TRAILER MARKER LAMPS

No.

Function

RE04

ENGINE MGT SYSTEM

RE05

IGNITION POWER

RE06

SPARE

RE07

SPARE

Fuses and Relays Center

Instrument Panel

The truck's fuses and relays are located

under the cover in the center of the

instrument panel.
There are decals under the cover which

notes the location of the fuses and

relays. Also, the purpose of each fuse

and relay is detailed.
The vehicle's normal exterior lighting is

controlled by control units. These

include control functions for each

respective lighting circuit. Should a

circuit be broken, due to overload or

short circuit , then a message display in

the Drivers Information Display (DID).

The function is reset when the fault has

been corrected.

Fuse and Relay Center

WARNING

Always replace fuses with the correct

rating. Never overfuse.

Never install a fuse higher than the

instructed rating.

NOTE

Set the electrical component in the "OFF"

position if possible, before changing the

fuse. The fuse holder can be burned, if the

voltage remains switched on.

259

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды