Mack M359 Скачать руководство пользователя страница 291

Страница: 291 / 332

MAINTENANCE, LUBRICATION AND SERVICE

TIRES, WHEELS AND HUB

Valve Stem

Measure the tread depth. The depth

should not be less than 3.2 mm (4/32-in)

on front tires and not less than 1.6 mm

(2/32-in) on drive tires.
Most premium steer tires start with 14.2

mm (18/32-in) tread depth when new.

Usually remove steer tires at 3.2 mm

(4/32-in). Drive tires should be removed

at not less than 1.6 mm (2/32-in).
It is important to have the wheels

correctly aligned. Check for uneven tire

wear frequently. Uneven tire wear is a

sign of wheels out of alignment.

Tire Hints

Hints on How to Avoid Unnecessary Tire

Wear

• Maintain correct tire pressure

• Check the tire pressure when the tires

are cold

• Check that valve caps are not missing

• Keep the wheels balanced

• Tire wear increases with speed

• Overloading not only decreases tire life

but also creates a hazard

• Incorrect front end alignment causes

increased wear
Dual mounted wheels should always be

of the same type and diameter

(maximum diameter difference allowed

is 6 mm (1/4 in).

Hubs

NOTE

Hub maintenance should be performed by

a certified technician.

Front Wheel Hubs

DANGER

Failure to keep wheel bearings properly

adjusted and lubricated may result in

accelerated tire wear, poor handling and,

in extreme cases, wheel separation from

the hub or from the spindle resulting in

loss of vehicle control and serious

personal injury or death.

Front Wheel Hubs

The front wheel hubs can be filled with

one of several types of oil. Motor oil

should be SAE 30 or 15W40. The oil can

be either petroleum based or synthetic.

Axle oil, API GL-5, SAE 75W-90, can

also be used. There are no set change

intervals for hub lubrication. The only

requirement is that if the hub is opened,

the lubricant must be changed.

Unitized Front Hubs

The non-tapered axle hubs are sealed

with lubricant inside the hub.

Pre-Set Rear Non-Driving Hubs

CAUTION

Do not remove the pre-set rear non-

driving hub sight glass for any reason.

Perform any lubrication refill at the hub

refill plug location. Removing the hub sight

glass will permanently damage the hub.

The hub will have to be replaced if the

sight glass is removed.

To determine if the pre-set rear non-

driving hub requires lubrication, view the

hub lubrication level via the hub front

glass. If lubrication is required, refill is

281

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды