Mack M359 Скачать руководство пользователя страница 150

Страница: 150 / 332

STARTING AND DRIVING

STARTING THE VEHICLE

WARNING

DO NOT work near the fan with the engine

running. The engine fan can engage at any

time without warning. Anyone near the fan

when it turns on could be seriously

injured. Before turning on the ignition, be

sure that no one is near the fan.

Priming the MP Fuel System

Unlock the hand primer pump by

pushing the pump handle in and

turning it counterclockwise.

Pump the hand primer until the force

of pumping increases.

NOTE

When the fuel system is empty, 200 or

more pump strokes can be required to

properly prime the system.

NOTE

There are NO bleed nipples to be opened

in order to prime the fuel system.

Lock the hand primer pump by

retracting it into the housing and

turning it clockwise.

Start the engine and run it at an

increased idle speed for

approximately 5 minutes to remove

any remaining air in the system.

Check the fuel system for leaks.

NOTE

If the engine does not start following this

procedure, contact your local certified

dealer.

Engine Warm-Up

CAUTION

Idling the engine unnecessarily for long

periods of time wastes fuel and fouls

injection nozzles. Unburned fuel causes

carbon formation and oil dilution. To avoid

engine damage, NEVER race an engine

during warm-up.

Engine damage can occur if the engine

is not warmed up to a minimum

operating temperature of 77°C (170°F)

before operating the vehicle.
Heavy-duty diesel engines are designed

to operate at optimum efficiency when

they are running loaded at normal

operating temperature. This condition is

where the most efficient combustion

takes place. When the engine is

operated unloaded, lightly loaded (such

as stop-and-go operations, PTO

operations, or periods of extended

engine idling) optimal operating

conditions are inhibited. Also, cold-

weather conditions, prevents the

achievement and maintaining of normal

operating temperature. As a result,

140

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды