Mack M359 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 332

background image

INTRODUCTION

WARRANTY CERTIFICATES

Standard Engine Warranty

Certificate (EPA 17 and

newer)

Mack Trucks warrants certain individual components of each new Mack MP®7, MP®8, and MP®10 EPA 17 and newer emission

engine in a new Mack truck to be free from defects in material and workmanship under normal use and service up to the periods

specified, provided all Mack Trucks' maintenance and inspection requirements are followed. See your local authorized Mack

dealer for recommended maintenance and inspection procedures. All warranty periods are calculated from the date in service of

the vehicle. All coverage is 100% for parts and labor subject to the qualifications, limitations, and exclusions as noted.
LIMITATIONS AND EXCLUSIONS TO THIS WARRANTY APPEAR ON THE FOLLOWING PAGES OF THIS CERTIFICATE.

THESE LIMITATIONS AND EXCLUSIONS ARE IMPORTANT AND MUST BE READ AND UNDERSTOOD.
This warranty applies to only new Mack MP®7, MP®8, and MP®10 engines meeting EPA 17 and newer emission requirements in

new Mack trucks operated in the United States and Canada.
Standard Mack Engine Components Coverage: 24 months or 250,000 miles (402 336 km), whichever occurs first, unless

otherwise noted.
Major Components Coverage: 60 months or 500,000 miles (804 672 km), whichever occurs first.
USE OF IMPROPER OR UNAPPROVED FUEL OR ENGINE OIL WILL VOID THE ENGINE AND AFTERTREATMENT SYSTEM

(DIESEL PARTICULATE FILTER) WARRANTIES. EPA 17 EMISSION MACK ENGINES REQUIRE THE USE OF MACK

SPECIFICATION EOS 4.5 HIGH PERFORMANCE DIESEL ENGINE OIL AND ULTRA LOW SULFUR DIESEL (ULSD) FUEL.
USE OF FLUIDS OTHER THAN API CERTIFIED DIESEL EXHAUST FLUID (DEF) WILL COMPROMISE AFTERTREATMENT

SYSTEM PERFORMANCE, INCREASE EMISSIONS, AND MAY IMPACT THIS TRUCK’S PRODUCT WARRANTIES.
SEE FOLLOWING TABLE FOR SPECIFIC COVERAGES:

Covered Standard Components List:

24 Months or 250,000 Miles (402 336 km )

Qualifications and Limitations

Air Compressor

Includes: Sprocket and Mounting Bolts

Bearings

All internally lubricated Bearings and Bushings only.

Camshaft, Caps, and Bolts

Failures resulting from the Valve and Injector adjustments not being maintained properly are

NOT covered. Normal maintenance adjustments are NOT covered.

Connecting Rods, Caps, and Bolts

28

X Publication_PC28

«
...
36
37
38
39
40
...
»

Содержание M359













































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M359

Бренд: Hino Страницы: 4

Бренд: Labrie Страницы: 112

Бренд: Mahindra Страницы: 55

Бренд: U-Line Страницы: 4

Бренд: Hino Страницы: 647

Бренд: Victory Страницы: 29

Бренд: TruckCraft Страницы: 28

Бренд: KOKE Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды