Mack M359 Скачать руководство пользователя страница 276

Страница: 276 / 332

MAINTENANCE, LUBRICATION AND SERVICE

DRIVE BELT ROUTING

mark (the shiny area on the pulley where

the belt rides). The witness mark should

be approximately the same width of the

belt.

Acceptable (Witness Mark Approximately

Same Width as Belt)

Not Acceptable (Witness Mark Tracking Off

Edge of Pulley)

Remove the belt by using a 1/2 inch

breaker bar to pull the tensioner back to

the install stop. Slowly return the

tensioner to the free-arm stop.
With the belt removed, use the breaker

bar to slowly pull the tensioner from the

free-arm stop to the install stop and then

slowly releasing it back to the free-arm

stop. Any excessive roughness or

hesitancy noticed while performing this

check indicates that the tensioner must

be replaced.

Check for metal-to-metal contact as

follows:
Check for contact between the arm and

the spring case. Replace if metal-to-

metal contact is seen.

Free-Arm Stop Position

Contact between Arm and Spring Case

Check.

Check for metal-to-metal contact

between the arm and the end cap.

Replace if contact is seen.

Contact between Arm and End Cap Check

266

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды