Mack M359 Скачать руководство пользователя страница 262

Страница: 262 / 332

MAINTENANCE, LUBRICATION AND SERVICE

ELECTRICAL SYSTEM

1 Green Dot visible

Any green appearance should be

interpreted as a green dot and means

that the battery is at or above a 65%

state of charge and is ready for use or

testing. This does not automatically

mean that the battery is in good

condition.

2 Green Dot not visible (Black Dot)

This indicates that the battery is below a

65% state of charge and must be

charged before testing. A black dot does

not mean that the battery is

automatically bad.

3 Clear or Light Yellow

This means that the electrolyte level is

below the level of the built-in

hydrometer, which may have been

caused by tipping of the battery, a

cracked case, or overcharging. This

battery should be replaced.

Battery Disconnect

The battery disconnect handle is located

under the cab above the top step on

driver side.
• Turn the battery disconnect handle

to the OFF position to prevent

battery rundown when truck is

parked for an extended time. The

battery disconnect handle can be

locked in the OFF position to prevent

tampering.

• Turn the battery disconnect handle

to the ON position to operate

vehicle.

Battery Disconnect Hanlde

Electric and Electronic

Systems

WARNING

Always wear eye protection when working

around batteries to prevent the risk of

injury due to contact with sulfuric acid or

an explosion.

Check regularly around the engine and

engine compartment for loose or frayed

wires. Have all loose or frayed electrical

wires and cables repaired before

operating the vehicle.

Grounding Practices

Proper grounding for vehicle and engine

electrical and electronic systems is

necessary for proper vehicle and engine

performance and reliability. Improper

grounding will result in uncontrolled and

unreliable electrical paths.
Uncontrolled engine electrical circuit

paths can result in damage to main

bearings, crankshaft journals surfaces

and aluminum components.

Uncontrolled electrical circuit paths can

also cause electrical noise which may

degrade vehicle and radio performance.
Operating engines without the engine-

to-frame ground strap installed can

cause damage to the engine. To prevent

electrical discharge damage, check to

252

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды