Mack M359 Скачать руководство пользователя страница 216

Страница: 216 / 332

EMISSION SOLUTION AND CONTROL

AFTERTREATMENT, MACK

Aftertreatment Tampering

When the SCR tampering fault is active for one or more hours, a new Driver Information Display (DID) screen appears. The text

changes for the Driver Information Display (DID) screen associated with this fault are listed in the following table.

Triggers

Aftertreatment

Tampering Indicator

Driver Information

Display Screen

No Fault

None

Tampering Fault Detected
Note: For examples of

the various SCR sensor

tampering types refer to the

“SCR Sensor Disconnected

Tampering Type” table

below.

SCR System Fault

Engine will Derate in approx.___ mins

Driving with Active Fault for

+ 1 hrs

SCR system fault.

Engine in derate

5 MPH limit in approx. <___mins
Note: Once this SCR

tampering fault occurs

the DID timer displays.

The timer displays the

minutes available before

the 5 mph derate occurs.

The timer can be cleared

using the Escape (ESC)

button on the stalk

switch control lever.

When the vehicle is

restarted after shutdown

the remaining minutes

before derate occurs will

reappear.

206

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды