Mack M359 Скачать руководство пользователя страница 40

Страница: 40 / 332

INTRODUCTION

WARRANTY CERTIFICATES

Covered Standard Components List:

24 Months or 250,000 Miles (402 336 km )

Qualifications and Limitations

Fuel Transfer Pump
Gaskets, Seals, O Rings, and Silicon Sealant
Gears

All internally lubricated Gears only (Timing and Idler Gears)

Hoses and Lines, Supplied with Engine

Fluid carrying: Engine to Engine Mounted

Idler Pulleys
Intake Manifold and Throttle Assembly
Ladder Frame
Oil Cooler

Engine Oil Cooler Only

Oil Fill Tube and Cap
Oil Filter Housing

Excludes: Oil Filters

Oil Pan
Oil Pump
Piston Assembly

Includes: Cooler Nozzles, Liners, Pistons, and Rings

Pneumatic Control System

TC Engine: Air Valve Unit, Buffer Valve Unit, and Check Valve

Power Steering Pump
Pre-Heater

Factory Installed Only. Includes: Preheat Relay, Terminals, and Power Cables

PTO Drive / REPTO (Rear Engine Mounted

PTO Drive)

Factory Installed Only. Excludes: All Pumps or Drive Gears

Rocker Arm Assembly and Shafts

Includes: PowerLeash™ Rockers and non- PowerLeash™ Rockers. Failures resulting from

the Valve and Injector Adjustments not being maintained properly are NOT covered. Normal

maintenance Adjustments are NOT covered.

Sensors (On Engine)

Includes: Coolant Temperature, Crankcase Pressure, Crankshaft (Engine Timing), EGR

Temperature and Pressure, Engine Oil Level and Temperature, Engine Oil Pressure, Engine

Position (Camshaft), Fuel Pressure and Temperature, Intake Boost Pressure and

Temperature, and Inlet Manifold Air (Temperature and Pressure)

Starter Motor
Thermostat (Coolant)

Includes: Thermostat Side Cover

X Publication_PC28

Содержание M359













































































































































































































































































































































Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды

Mack M359, Руководство пользователя

Результаты поиска

Содержание M359

Отзывы:

Похожие инструкции для M359

Бренды по названию

Популярные бренды