Loepfe YarnMaster Zenit Скачать руководство пользователя страница 68

Страница: 68 / 83

ZENIT

REPORTS AND DIAGNOSIS

Message

Explanation / Cause

Action

Spindle x : D Sensing Light
out of Range

Light sensor for scanning the yarn diameter
out of tolerance.
Optic dirty.
TK defective.

Clean optic.
Start spindle briefly.
Replace TK, and perform Reset AWE.
Replace AWE and perform Reset AWE.

Spindle x : F Adjust Error

Optical system for foreign matter detection dirty.
Yarn count or yarn color outside of sensing head range.
Large number of foreign fibers succeeding one another.

Clean optic.
Repeat adjust.
Check yarn count or color respectively.
Change bobbins.
Use different spindle for Adjust.

Spindle x : F Sensing Light
out of Range

Light sensor for foreign matter detection
out of tolerance.
Optic dirty.
Incorrect setting.
TK defective.

Clean optic.
Start spindle briefly.
Replace TK, and perform Reset AWE.
Replace AWE and perform Reset AWE.

Spindle x : Group number: ???

AWE which is not assigned to a group.
Assignment of group number lacking.

Assign all spindles to group.

Spindle x : Incompatible AWE
software version

AWE reports a wrong software version.

Install correct AWE software
Exchange AWE and perform Reset AWE.

Spindle x : Invalid AWE Ma
chine Type

AWE reports a wrong machine type,
i. e. the wrong AWE software was loaded.

Check AWE software.
Import correct AWE software.
Exchange AWE and perform Reset AWE.

Spindle x : No Sensing Head

No TK connected.

Insert TK.
Check connector.

Spindle x : No Speed Informa
tion

Drum signals lacking.
Cable break.
Sensor or spindle computer defective.

Start spindle briefly.
Replace AWE and perform Reset AWE.
Exchange sensor or spindle computer.

Spindle x : No Yarn Break

Knife locked through fiber accumulation.
Knife dull.
Sensing head coil ruptured.
Knife power supply lacking.

Clean TK.
Exchange knife.
Check knife power supply.
Replace TK / AWE and perform Reset AWE.

Spindle x : Reduced TK func
tionality! Functionality of
whole group reduced!

The TK version has fewer functions than the rest
of the production group.

Exchange TK.
Adapt the spindle range of the group.

Spindle x : System Alarm

System error.
Electrical interference.
Defective AWE.

Perform Reset AWE.
Replace AWE and perform Reset AWE.

Spindle x : Locked

System-dependent AWE alarm.

Perform Reset AWE.
Replace AWE and perform Reset AWE.

Spindle x: Offline

No communication.
AWE does not communicate with ZE.

Perform Reset AWE.
Replace AWE and perform Reset AWE.

Startup Adjust for Group x

New unit software was installed.
An adjustment was performed during the start
on each spindle.

None

Содержание YarnMaster Zenit




















































































Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды

Loepfe YarnMaster Zenit, Инструкция по эксплуатации

Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды