Loepfe YarnMaster Zenit Скачать руководство пользователя страница 55

Страница: 55 / 83

ZENIT

FOREIGN MATTER

P Settings

With the TK YM ZENIT FP sensing head, it is possible to de-
tect synthetic foreign matter, e. g. polypropylene, polyamide
(nylon).

To ensure the function of the P Sensor, the yarn to be
wound must not be wet.

Note

Existing YarnMaster Zenit F equipment can be retrofit-

ted by mounting the P sensor on the sensing head.

Limit

The limit (0.5-9.9) determines the sensitivity of P Clearing.
The setting must be adapted according to type and charac-
teristics of the yarn to be processed.

During the splice check, the P Sensor is switched
to“insensitive”.

Ref. Length

TK FP C

0.5 – 4.0 cm

TK FP C P2

1.0– 8.0 cm

The reference length is used to set the fault length of the for-
eign matter to be detected.

Setting examples

(Guide values)

TK FP C

Insensitive setting

Limit: 3.0

Ref. Length: 2.5

Sensitive setting

Limit: 2.0

Ref. Length: 2.0

TK FP C P2

Insensitive setting

Limit: 8.0

Ref. Length: 2.0

Sensitive setting

Limit: 4.0

Ref. Length: 2.0

Содержание YarnMaster Zenit




















































































Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды

Loepfe YarnMaster Zenit, Инструкция по эксплуатации

Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды