Loepfe YarnMaster Zenit Скачать руководство пользователя страница 24

Страница: 24 / 83

ZENIT

OPERATING

Adjust

Initial Startup / Change of Software

To compensate for the deviations of the individual spindles,
an automatic Spindle Adjust

on all spindles

is performed

during the first adjustment after the startup of the equipment
or after a software change.

The following message box is displayed:

“ Startup Adjust for

Group x”.

During the automatic Spindle Adjust, the first 80 m of
yarn on all spindles are not cleared.

Note :

If sensing heads are replaced on a machine, a manual

Spindle Adjust has to be carried out on these spindles. (See

Diagnosis

menu.)

Putting into Operation / Lot Change

When putting the system into operation and for every lot
change, it must be defined how the yarn to be wound is to be
cleared, i. e. which quality is to be guaranteed by the clearer:

The clearer channel setting must define the clearer limit.

By means of adjustment, the current yarn count or yarn
structure, respectively, must be read in and the basic val-
ue determined.

Lot Start

Before every lot start, it must be ensured that the
correct clearer settings were assigned to the re-
spective group.

Содержание YarnMaster Zenit




















































































Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды

Loepfe YarnMaster Zenit, Инструкция по эксплуатации

Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды