Loepfe YarnMaster Zenit Скачать руководство пользователя страница 56

Страница: 56 / 83

ZENIT

MONITORING DATA

Monitoring Data

Cut Data

The total of all cut faults or events relative to the length dis-
played in

Cut Declaration

This data can be optionally viewed per spindle or group.

Note :

When the sums of the Nep Cuts, Short Cuts, Long

Cuts and Thin Cuts are compared with Total Cuts in the corre-
sponding classification window, differences are possible be-
cause, depending on the setting, cuts can also be performed
outside the displayed classes.

Cuts

Total Yarn Cuts

Total of textile yarn faults

Short Off Count Cuts

Yarn count deviation cuts in the short

count range

Off Count Cuts

Yarn count deviation cuts

SFI/D Cuts

Surface index cuts

F Cuts

Foreign matter cuts

P Cuts

Synthetic foreign matter cuts:

PP, PE etc.)

Short Cluster Cuts

Short fault cluster cuts

Long Cluster Cuts

Long fault cluster cuts

Thin Cluster Cuts

Thin place cluster cuts

F Cluster Cuts

Foreign matter cluster cuts

VCV Cuts

Cut resulting from a deviation of the
VCV value from the mean value

Bunch Cuts

Cuts caused by bunches or similar
running faults

DBunch Cuts

Delayed cuts caused by bunches or
similar running faults

Upper Yarn Cuts

Cut caused by double yarn of the
cone

Splices

Splice Cuts

Cut splices

Splices

Total of all wound splices

Splice Repetitions

Caused by splice cuts, upper yarn
cuts, splices not completed

Alarms

Number of blockages after exceeding the set number of rep-
etitions of the group or spindle.

Содержание YarnMaster Zenit




















































































Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды

Loepfe YarnMaster Zenit, Инструкция по эксплуатации

Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды