Loepfe YarnMaster Zenit Скачать руководство пользователя страница 63

Страница: 63 / 83

ZENIT

CHART

Chart

Grafic representation of the cut data shown in the

Data Item

List

in form of a bar chart.

Blue bars

The values are scaled to the set

Window Length

Green bars

The values are absolute for the length wound up
to then.

Note :

As long as the set length is not

reached by all spindles, of the group the cut num-
bers can still vary!

Red Line

The red line shows the mean value of the cut da-
ta, calculated over the wound length.

Length

Wound length (

Window Length

) in kilometers to

which the cut data refer.

Selection of Cut Data

Group / Machine

With + or – the representation of an indi-

vidual group or an overview over the whole machine can be
selected.

Spindle

If a single spindle is selected, it is marked red in the

chart. Tapping the chart displays the cut data of this spindle.

Scale

Full Range

Scale from zero to the highest value of the dis-

played group.

Optimized Range (Spread)

Scale from the lowest to the

highest value of the displayed group. This representation is
used to make the deflection better visible.

Relative Range

Negative and positive deviations of the val-

ues of the spindles from the mean value.

Percentage

Negative and positive deviations of the spindles

from the mean value in percent.

Values

The cut data of the spindles can be shown or hidden.

Содержание YarnMaster Zenit




















































































Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды

Loepfe YarnMaster Zenit, Инструкция по эксплуатации

Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды