Loepfe YarnMaster Zenit Скачать руководство пользователя страница 27

Страница: 27 / 83

ZENIT

DIALOG

Access Level / Password

To prevent the modification or deletion of data by unauthor-
ized persons, data inputs are protected with passwords.

If a menu item is tapped which is protected with a password,
the

Access Level

window is displayed. The required password

level is shown in

Password Level

Enter the new password (5 numbers max.) on the displayed
keyboard and confirm with

The following four password levels exist:

Display

Operator

Foreman

Service

Password Level Display

: Most of the data and settings can

also be viewed and printed without password.

Changing the Password

During the startup, the foreman password is 1291, the opera-
tor password is 4711.

It is recommended to change these passwords after
startup!

•

Tap

Foreman Password

Operator Passwor

d, respectively.

•

Enter the new password on the displayed keyboard and
confirm with

•

Confirm the changed password with

Yes

Содержание YarnMaster Zenit




















































































Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды

Loepfe YarnMaster Zenit, Инструкция по эксплуатации

Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды