Loepfe YarnMaster Zenit Скачать руководство пользователя страница 43

Страница: 43 / 83

ZENIT

YARN STRUCTURE

Off Count

These settings make possible the detection of false bobbins
or yarn with a larger off-count deviation.

+ DiaDiff /– DiaDiff

Depending on the quality or irregularity of the yarn, a dia-
meter deviation between ±3% and ±44% (difference to ba-
sic value) can be selected. It can be set independently for the
positive as well as negative diameter deviation.

Coarse / Fine

According to the diameter deviation set, the yarn count devia-
tion is displayed for

Coarse

and

Fine

CntLen

The reference length in which the average diameter differ-
ence is determined can be set between

10 and 50 m

This

allows for optimizing the detection of bobbin misplacements
and count variations.

+ Cuts /– Cuts

The number of cuts due to a positive or negative deviation of
the yarn diameter are listed separately.

This display makes possible the optimizing of the settings.

Short Off Count

CntLen

As opposed to the yarn count channel, the shorts count chan-
nel allows separate acquisition of yarn with a

count devia

tion over a length of less than 10 m.

The reference length

determining the average yarn count deviation can be set be-
tween 1 and 32 m.

Содержание YarnMaster Zenit




















































































Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды

Loepfe YarnMaster Zenit, Инструкция по эксплуатации

Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды